20×145 SW UYS Brûlé Brossé AB Cynamon
On request
UTS
UTS profile — the standard finish for thermo pine cladding, for vertical or horizontal installation. Scandinavian thermally modified pine, modified use class 3, biocide-free, compatible with RE2020 and already anticipating RE2028 (1 January 2026).
23
products
20×124 Pin UYS Brûlé Brossé A Cynamon
On request
23×68 Épicéa ROMBx1 classe AB
On request
20×145 SW UYS Brûlé Brossé AB Tan
On request
20×145 SW UYS Brûlé Brossé AB Dark Night
On request
20×124 charred brushed pine UYS A Dark Night
On request
FACADE Scandinavian Spruce 19×189 class AB
On request
28×146 Scandinavian Spruce PÓŁBAL class AB
On request
19×68 Thermo Sosna UTS class AB
On request
15×120 Alder UTS class A
On request
42×68 Thermo Sosna UTS class AB
On request
Brushed Thermo Pin board 19×140 Faza+ BALTIC GRAY class AB
On request
34×146 Pine/spruce log beam, ceiling-floor, facade PHASE C+C class AB
On request
FACADE Scandinavian Spruce 19×196 class AB
On request
15×90 Alder UTS class A
On request
Brushed Thermo Pin board 19×140 Faza+ SPECIAL BLACK class AB
On request
19×92 Thermo Sosna UTS class AB
On request
34×146 Pine/Spruce Log beam, ceiling-floor, facade PHASE C+C class C
On request
19×140 Thermo Sosna UTS class AB
On request
19×117 Thermo Sosna UTS class AB
On request
24×146 Scandinavian Spruce PÓŁBAL class AB
On request
15×90 Scandinavian Spruce STS class C
On request
19×140 Thermo Pin UTS+ Colorless class AB
On request
Top sellers in this category
The profile at a glance
The UTS profile belongs to the Dartank thermally modified pine cladding family. Every one of our references is made from Scandinavian pine thermally modified at 200 °C, with no chemicals whatsoever. The wood fibre is modified right the way through — high dimensional stability, greater resistance to fungi and insects.
Ventilated installation — the essential rules
Fitted on vertical or horizontal battens, with a breather membrane mandatory behind and a ventilated air gap of at least 20 mm. Fixings in A2 stainless steel (A4 by the sea) — Torx screws with a reduced countersunk head, or concealed clips depending on the profile.
Compliant with the requirements of DTU 41.2 (the French standard for exterior timber cladding).
Natural silver-grey patina
Left untreated, thermally modified pine turns a natural silver-grey within 8 to 18 months — a look much sought after in contemporary architecture. With a saturating oil applied every 2 to 4 years, the original brown tone is preserved.
Help & advice
Frequently asked questions
Everything you need to know before ordering. Another question? Contact us.
UTS is a cladding profile in thermally modified pine — a specific machining of the board (grooves, chamfer, spacing) that defines its architectural look and the way it is fixed. It belongs to the Dartank thermo-pine cladding family, in modified use class 3.
An air gap of at least 20 to 25 mm between the breather membrane and the cladding. It is essential for moisture to escape — without it the timber will rot, even when thermally modified.
Not necessarily. Left untreated, thermo-pine turns a natural silver grey within 8 to 18 months — a look much sought after in contemporary architecture. With a saturating wood oil (every 2-4 years), the brown tone is preserved.
A2 stainless steel screws (standard façades) or A4 (coastal locations, salt-laden air). Small countersunk head with a Torx drive; professional brands: SPAX Façade, Essve, RothoBlaas, PGB.